Motocross gate

camilles5
Profile picture for user camilles5
Posts
4
Joined
10/2/2019
Location
New London, NC US
camilles5
Edited Date/Time 10/10/2019 6:32pm
Looking for good pictures of up close motocross gates and pictures inside the dog house to get ideas on how to build my own. Looking for a layout on how to efficiently raise and drop the gate. Preferably manual dropping system. Looking for metal and welded good moto gate layout. Thanks in advance!
1
|
greenmx5
Profile picture for user greenmx5
Posts
1641
Joined
4/1/2014
Location
PA US
greenmx5 10/2/2019 8:14am
10/2/2019 8:14am
Here's the redneck option. Get's the job done and increases reaction time I suppose

8
Brent_Apodaca 10/2/2019 12:30pm
10/2/2019 12:30pm
greenmx5 wrote:
Here's the redneck option. Get's the job done and increases reaction time I suppose
Here's the redneck option. Get's the job done and increases reaction time I suppose

To add to this , if you go to a Tractor supply they usually have scrap wood in the back that is typically used in packaging. You could use that as your base box. Then your only expense would be a few 2X4's and door hinges.
dl117
Profile picture for user dl117
Posts
1548
Joined
2/8/2007
Location
Cambridge, MN US
Fantasy
2800th
dl117 10/2/2019 12:37pm
10/2/2019 12:37pm
greenmx5 wrote:
Here's the redneck option. Get's the job done and increases reaction time I suppose
Here's the redneck option. Get's the job done and increases reaction time I suppose

Brent_Apodaca wrote:
To add to this , if you go to a Tractor supply they usually have scrap wood in the back that is typically used in packaging...
To add to this , if you go to a Tractor supply they usually have scrap wood in the back that is typically used in packaging. You could use that as your base box. Then your only expense would be a few 2X4's and door hinges.
that really aint that bad of an option, and I work in the lumber business......soooo

The Shop

See All »
dirtbikemike 10/2/2019 5:59pm
10/2/2019 5:59pm










This is my 15 rider gate that I used for fair races. I'm only using 8 gates on my personal AX track now.

3
camilles5
Profile picture for user camilles5
Posts
4
Joined
10/2/2019
Location
New London, NC US
camilles5 10/3/2019 12:50pm
10/3/2019 12:50pm
dirtbikemike wrote:
[img]https://p.vitalmx.com/photos/forums/2019/10/02/377262/s1200_startinggate_008.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377263/s1200_startinggate_009.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377264/s1200_startinggate_006.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377265/s1200_startinggate_004.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377270/s1200_startinggate_002.jpg[/img] This is my 15 rider gate that I used for fair races. I'm only using 8 gates on my personal AX...










This is my 15 rider gate that I used for fair races. I'm only using 8 gates on my personal AX track now.

Do you have the measurements on the pieces that connect the two big angle irons. The flat piece that the pipe runs through Is what I’m talking about??
clemsonsc
Profile picture for user clemsonsc
Posts
93
Joined
3/12/2019
Location
Flat Rock, NC US
clemsonsc 10/3/2019 6:13pm
10/3/2019 6:13pm
I have built a few gates ranging from 3-40 bikes. I’m only about 2 1/2 hrs from you.
1
dirtbikemike 10/4/2019 6:17pm
10/4/2019 6:17pm
dirtbikemike wrote:
[img]https://p.vitalmx.com/photos/forums/2019/10/02/377262/s1200_startinggate_008.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377263/s1200_startinggate_009.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377264/s1200_startinggate_006.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377265/s1200_startinggate_004.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377270/s1200_startinggate_002.jpg[/img] This is my 15 rider gate that I used for fair races. I'm only using 8 gates on my personal AX...










This is my 15 rider gate that I used for fair races. I'm only using 8 gates on my personal AX track now.

camilles5 wrote:
Do you have the measurements on the pieces that connect the two big angle irons. The flat piece that the pipe runs through Is what I’m...
Do you have the measurements on the pieces that connect the two big angle irons. The flat piece that the pipe runs through Is what I’m talking about??
I'll put a tape on it this weekend for you.
JustMX
Profile picture for user JustMX
Posts
4838
Joined
4/1/2008
Location
TN US
JustMX 10/4/2019 8:09pm
10/4/2019 8:09pm Edited Date/Time 10/4/2019 9:38pm
A big change in gate design lately has been that instead of the pipe running through a hole cut in the flat, verticle pieces that run between the angle pieces is that some companies are now making that a U shaped cut out, and then lining it on the bottom side with half pieces of pipe (picture a rod bearing insert from car engine).

This is a much better design than the holes.

It allows repairs to be made on the pipe that works as a cam to lift the gates. It also simplifies installation because the frames can be put in and secured, and then the cam pipes and gate loops put in.

I ran races for 15 years and had up to 4 different tracks at the same time. Several were home made and there were alway small difference in hole placement on stuff like the gate loop mounting brackets.

We started welding 1/2" Coupler nuts at 90 degrees on the flat gate cams and then putting a carriage bolt in them to hit the gate.

This allowed each gate loop heighth to be adjusted so when the gate was cocked they would all be even.

I also did this on the gate used at muddy creek.

Finally, if you can get a fabrication shop to cut some plate steel it is,a good idea to make covers for the hole in the gate frame between 5he 2 pieces of angle. They need to be slightly smaller than the inside measurement of the gate loops.

This keeps you from having to do constant digging around the gate from and the cams.
camilles5
Profile picture for user camilles5
Posts
4
Joined
10/2/2019
Location
New London, NC US
camilles5 10/5/2019 6:44am
10/5/2019 6:44am
clemsonsc wrote:
I have built a few gates ranging from 3-40 bikes. I’m only about 2 1/2 hrs from you.
I have all the bent gate pieces, also have the flat pieces that will connect the big angle iron. Just wanting to do a stomp dropping mechanism and not sure how to go about that.
dirtbikemike 10/10/2019 6:32pm
10/10/2019 6:32pm
dirtbikemike wrote:
[img]https://p.vitalmx.com/photos/forums/2019/10/02/377262/s1200_startinggate_008.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377263/s1200_startinggate_009.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377264/s1200_startinggate_006.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377265/s1200_startinggate_004.jpg[/img] [img]https://p.vitalmx.com/photos/forums/2019/10/02/377270/s1200_startinggate_002.jpg[/img] This is my 15 rider gate that I used for fair races. I'm only using 8 gates on my personal AX...










This is my 15 rider gate that I used for fair races. I'm only using 8 gates on my personal AX track now.

camilles5 wrote:
Do you have the measurements on the pieces that connect the two big angle irons. The flat piece that the pipe runs through Is what I’m...
Do you have the measurements on the pieces that connect the two big angle irons. The flat piece that the pipe runs through Is what I’m talking about??
We haven't used this gate since last winter, so I had to dig some grass away. The vertical flat bars are 16 inches. The gate cocker has the receptacle pipe and the locking tab welded on at a specific angle. You can adjust the gate height by drilling extra holes in the kicker arm. Of course all the dirt needs to be cleaned from around the main pipe so it can turn when the gates are dropped. The end of the kicker where it meets the tab needs to have a radius for smooth operation.










Post a reply to: Motocross gate