Kx450f Motor Zero hours

ge217
Profile picture for user ge217
Posts
753
Joined
12/4/2013
Location
Vero Beach, FL US
ge217
Edited Date/Time 11/17/2015 7:46am
Asking $2700 obo
2012-2015 motor (believe it will fit 2009-2015).
Motor was a 2012 but was completely rebuilt this year and has not been used since.

~New cases
~Crank
~Valves
~Valve springs
~Valve guide seals
~Cylinder
~Piston and rings
~Main bearings
~All trans mission bearings due to new cases
~Transmission shafts
~All but 3 transmission gears are new
All oem parts, motor does come with wiring harness as well.









|
ge217
Profile picture for user ge217
Posts
753
Joined
12/4/2013
Location
Vero Beach, FL US
ge217 10/13/2015 5:06pm
10/13/2015 5:06pm
......

The Shop

See All »
ge217
Profile picture for user ge217
Posts
753
Joined
12/4/2013
Location
Vero Beach, FL US
ge217 11/16/2015 2:04pm
11/16/2015 2:04pm
bump
cmotodad
Profile picture for user cmotodad
Posts
952
Joined
12/18/2013
Location
Yorba Linda, CA US
cmotodad 11/16/2015 7:18pm
11/16/2015 7:18pm
I the frame getting ready for a K5?
ge217
Profile picture for user ge217
Posts
753
Joined
12/4/2013
Location
Vero Beach, FL US
ge217 11/17/2015 7:07am
11/17/2015 7:07am
cmotodad wrote:
I the frame getting ready for a K5?
No. This is just a spare motor. Last time I did a conversion it didn't go well. Scared to do and ride another one. If I did offroad only I probably would but not since I would ride it on moto 95% of the time. I was lucky enough to walk away from it once don't know if I would be that lucky if it happen again.

WileCyot
Profile picture for user WileCyot
Posts
459
Joined
9/23/2014
Location
Katy, TX US
WileCyot 11/17/2015 7:37am
11/17/2015 7:37am
cmotodad wrote:
I the frame getting ready for a K5?
ge217 wrote:
No. This is just a spare motor. Last time I did a conversion it didn't go well. Scared to do and ride another one. If I...
No. This is just a spare motor. Last time I did a conversion it didn't go well. Scared to do and ride another one. If I did offroad only I probably would but not since I would ride it on moto 95% of the time. I was lucky enough to walk away from it once don't know if I would be that lucky if it happen again.

Looks like those lower welds had poor weld quality and then took the upper frame tubes with it. That's a damn shame.
ge217
Profile picture for user ge217
Posts
753
Joined
12/4/2013
Location
Vero Beach, FL US
ge217 11/17/2015 7:46am
11/17/2015 7:46am
cmotodad wrote:
I the frame getting ready for a K5?
ge217 wrote:
No. This is just a spare motor. Last time I did a conversion it didn't go well. Scared to do and ride another one. If I...
No. This is just a spare motor. Last time I did a conversion it didn't go well. Scared to do and ride another one. If I did offroad only I probably would but not since I would ride it on moto 95% of the time. I was lucky enough to walk away from it once don't know if I would be that lucky if it happen again.

WileCyot wrote:
Looks like those lower welds had poor weld quality and then took the upper frame tubes with it. That's a damn shame.
Considering you can barely see those welds idk how you would be able to tell that from the pic.. But I can assure you that the weld wasn't poor quality. Do some research, you'll stumble across more of these frame just like this. Cr's as well. Was even told by a very reliably source at kawasaki that the Af 250's they built did the same thing.

Post a reply to: Kx450f Motor Zero hours