Fast By Ferracci Husqvarna Cr 250 help needed?/ Build

wpark89
Profile picture for user wpark89
Posts
1136
Joined
12/9/2009
Location
Mattawa, WA US
wpark89 11/20/2021 9:13am
11/20/2021 9:13am
StormWorks wrote:
I ve tried to compile a list of riders that were teamed up with Fast by ferracci that I have seen images of So there are...
I ve tried to compile a list of riders that were teamed up with Fast by ferracci that I have seen images of
So there are a few unknowns so far I got in no particular year order just numerical

#1 - Alessio Chiodi in GPs when he went back at end of 2000 season
#3 - ?
#6 - Steve Lamson
#36 - Jason Thomas
#40 - Travis Preston
#44 - Damian Plotts
#51 - Chris Gosselar
#70 - David Kratz
#73 - Paul Carpenter
#96 - David Veracka
#109 - Alessio Chiodi
#115 - Robbie Skaggs
#120 - Steve Mertens
#131 - Brian Mcgavron
#151 - ?
#247 - Tyler Evans
#319 - ?
#980 - ?
#991 Thomas Traversini

Any help filling in the blanks or corrections would be great
Would be interested to see what picture you have of me
Wesley Parker 319…I was a local pro from WA State, I did a few Canadian Nationals that year and Hangtown on a 125 and Washougal on a 250.

Besides the guys on your list I remember MXA’s Dennis Stapleton qualified for 1 or 2 125 Nationals in 00 on a Husky. Also there was the Moto Xtremes Husky team out of Ohio or Indiana. David Oettel from Wisconsin was National number 98 or 99 and made some motos. Also, after the Ferracci team was done in 02 I believe Willy Browning raced some East Cost 125 SX in 03 on a Husky. I can’t remember by numbers for sure but the 980 may be Daniel Blair…he rode 1 race in 2002 (Hangtown) on a FBF 125.
6
wpark89
Profile picture for user wpark89
Posts
1136
Joined
12/9/2009
Location
Mattawa, WA US
wpark89 11/20/2021 9:22am
11/20/2021 9:22am Edited Date/Time 11/20/2021 9:23am
Thain was #211 in the 03 125 GPs.

1
StormWorks 11/20/2021 9:35am
11/20/2021 9:35am
wpark89 wrote:
Thain was #211 in the 03 125 GPs. [img]https://p.vitalmx.com/photos/forums/2021/11/20/519134/s1200_524EED1F_E8DD_400D_B2F5_9E35C7A4925B.jpg[/img]
Thain was #211 in the 03 125 GPs.

Yeah he did Paris bercy sx in 02 on a husky with UFO gear but I don’t know what number he was that’s why I though maybe 319
StormWorks 11/20/2021 9:37am
11/20/2021 9:37am
StormWorks wrote:
I ve tried to compile a list of riders that were teamed up with Fast by ferracci that I have seen images of So there are...
I ve tried to compile a list of riders that were teamed up with Fast by ferracci that I have seen images of
So there are a few unknowns so far I got in no particular year order just numerical

#1 - Alessio Chiodi in GPs when he went back at end of 2000 season
#3 - ?
#6 - Steve Lamson
#36 - Jason Thomas
#40 - Travis Preston
#44 - Damian Plotts
#51 - Chris Gosselar
#70 - David Kratz
#73 - Paul Carpenter
#96 - David Veracka
#109 - Alessio Chiodi
#115 - Robbie Skaggs
#120 - Steve Mertens
#131 - Brian Mcgavron
#151 - ?
#247 - Tyler Evans
#319 - ?
#980 - ?
#991 Thomas Traversini

Any help filling in the blanks or corrections would be great
wpark89 wrote:
Would be interested to see what picture you have of me Wesley Parker 319…I was a local pro from WA State, I did a few Canadian...
Would be interested to see what picture you have of me
Wesley Parker 319…I was a local pro from WA State, I did a few Canadian Nationals that year and Hangtown on a 125 and Washougal on a 250.

Besides the guys on your list I remember MXA’s Dennis Stapleton qualified for 1 or 2 125 Nationals in 00 on a Husky. Also there was the Moto Xtremes Husky team out of Ohio or Indiana. David Oettel from Wisconsin was National number 98 or 99 and made some motos. Also, after the Ferracci team was done in 02 I believe Willy Browning raced some East Cost 125 SX in 03 on a Husky. I can’t remember by numbers for sure but the 980 may be Daniel Blair…he rode 1 race in 2002 (Hangtown) on a FBF 125.
I will post he photo I have

The Shop

See All »
caviar&cigarettes338 11/20/2021 9:41am
11/20/2021 9:41am
StormWorks wrote:
I ve tried to compile a list of riders that were teamed up with Fast by ferracci that I have seen images of So there are...
I ve tried to compile a list of riders that were teamed up with Fast by ferracci that I have seen images of
So there are a few unknowns so far I got in no particular year order just numerical

#1 - Alessio Chiodi in GPs when he went back at end of 2000 season
#3 - ?
#6 - Steve Lamson
#36 - Jason Thomas
#40 - Travis Preston
#44 - Damian Plotts
#51 - Chris Gosselar
#70 - David Kratz
#73 - Paul Carpenter
#96 - David Veracka
#109 - Alessio Chiodi
#115 - Robbie Skaggs
#120 - Steve Mertens
#131 - Brian Mcgavron
#151 - ?
#247 - Tyler Evans
#319 - ?
#980 - ?
#991 Thomas Traversini

Any help filling in the blanks or corrections would be great
I been trying look some riders up and found Jim Neese looks like he was a Ferracci support rider at LL then turned pro raced few races for them . Not 100% sure on that through
TK40_FC
Profile picture for user TK40_FC
Posts
442
Joined
5/17/2021
Location
Canton, OH US
TK40_FC 11/20/2021 1:44pm
11/20/2021 1:44pm
Cool thread and build, feel like I received an entire education about the FBF team. Kudos to all the guys stepping up to help this member out with parts and knowledge as well! Bike should be sweet when done.
4
caviar&cigarettes338 11/20/2021 4:57pm
11/20/2021 4:57pm
TK40_FC wrote:
Cool thread and build, feel like I received an entire education about the FBF team. Kudos to all the guys stepping up to help this member...
Cool thread and build, feel like I received an entire education about the FBF team. Kudos to all the guys stepping up to help this member out with parts and knowledge as well! Bike should be sweet when done.
I can’t thank everyone on here enough . If it wasn’t for members here I would still have the same beat up husky with metal mulisha graphics, blue painted procircuit pipe and blue spoke skins .
aeffertz
Profile picture for user aeffertz
Posts
10021
Joined
7/16/2015
Location
La Crosse, WI US
aeffertz 11/20/2021 5:09pm
11/20/2021 5:09pm
I knew I wouldn’t be of any help when I saw this thread title so I never bothered to click. But after seeing it bumped to the top all the time I decided to check it out. I’m glad I did, this is awesome! Good luck with the build!
2
BobPA
Profile picture for user BobPA
Posts
8143
Joined
10/31/2013
Location
PA US
BobPA 11/20/2021 5:18pm
11/20/2021 5:18pm
I completely spaced and forgot to ship your posters, my bad man. I'll get them out this week
1
SLAPAHO
Profile picture for user SLAPAHO
Posts
1680
Joined
8/15/2006
Location
Newport Beach, CA US
Fantasy
1510th
SLAPAHO 11/20/2021 5:46pm
11/20/2021 5:46pm
Robbie Skaggs' bike. 2000 High Point



4
caviar&cigarettes338 11/20/2021 5:50pm
11/20/2021 5:50pm
BobPA wrote:
I completely spaced and forgot to ship your posters, my bad man. I'll get them out this week
Thanks let me know in pm what I owe you for shipping thanks again!!
Austin_Rankin 11/20/2021 7:07pm
11/20/2021 7:07pm
I have a whole cr125 engine i need to get rid of, engine has no clutch basket and no piston but cylinder is in awesome shape. I have no use for it at all.
FlyingBob
Profile picture for user FlyingBob
Posts
36
Joined
11/10/2021
Location
OutThere, VA US
FlyingBob 11/20/2021 7:38pm
11/20/2021 7:38pm
caviar&cigarettes338 wrote:
That cone pipe looks so cool !!
Mr. Robinson wrote:
It was a Scalvini pipe. It looked super cool, but I actually liked the DEP and PC pipes better. You can barely see the back side...
It was a Scalvini pipe. It looked super cool, but I actually liked the DEP and PC pipes better. You can barely see the back side of the CDI bracket in this picture. This CDI had a single piece plug connector, instead of the two piece that the '02 CR250 had. FBF was no help, so I had to figure out how to hook it up. Finally found a KX harness that had a plug that would mate to the box. Then figure out how to pin it out. I didn't like the connector sticking out to the side, so I mounted it pointing up. This was the second 250 I built. It actually started as a 300, but I didn't like it as much as the 250, so I swapped out the top end for 250 stuff.


Small world. Here's the pipe. Been hanging in my garage for about 5 years! Gonna clean it up tomorrow.
7
Mr. Robinson 11/21/2021 8:48am
11/21/2021 8:48am
caviar&cigarettes338 wrote:
That cone pipe looks so cool !!
Mr. Robinson wrote:
It was a Scalvini pipe. It looked super cool, but I actually liked the DEP and PC pipes better. You can barely see the back side...
It was a Scalvini pipe. It looked super cool, but I actually liked the DEP and PC pipes better. You can barely see the back side of the CDI bracket in this picture. This CDI had a single piece plug connector, instead of the two piece that the '02 CR250 had. FBF was no help, so I had to figure out how to hook it up. Finally found a KX harness that had a plug that would mate to the box. Then figure out how to pin it out. I didn't like the connector sticking out to the side, so I mounted it pointing up. This was the second 250 I built. It actually started as a 300, but I didn't like it as much as the 250, so I swapped out the top end for 250 stuff.


FlyingBob wrote:
Small world. Here's the pipe. Been hanging in my garage for about 5 years! Gonna clean it up tomorrow. [img]https://p.vitalmx.com/photos/forums/2021/11/20/519169/s1200_KRWR250pipe1.jpg[/img]
Small world. Here's the pipe. Been hanging in my garage for about 5 years! Gonna clean it up tomorrow.
If I remember right, it will actually bolt right up to the his bike. Pretty sure all that stuff swaps over from around '99 to '12.
1
caviar&cigarettes338 11/21/2021 9:19am
11/21/2021 9:19am Edited Date/Time 11/21/2021 9:20am
Got rear all laced up just need true wheel and will call it a day and do front next week when I get spare front wheel and hub and spokes from Rob in Ontario Canada
5

Pit Row

See All »
StormWorks 11/21/2021 9:40am
11/21/2021 9:40am
Mr. Robinson wrote:
It was a Scalvini pipe. It looked super cool, but I actually liked the DEP and PC pipes better. You can barely see the back side...
It was a Scalvini pipe. It looked super cool, but I actually liked the DEP and PC pipes better. You can barely see the back side of the CDI bracket in this picture. This CDI had a single piece plug connector, instead of the two piece that the '02 CR250 had. FBF was no help, so I had to figure out how to hook it up. Finally found a KX harness that had a plug that would mate to the box. Then figure out how to pin it out. I didn't like the connector sticking out to the side, so I mounted it pointing up. This was the second 250 I built. It actually started as a 300, but I didn't like it as much as the 250, so I swapped out the top end for 250 stuff.


FlyingBob wrote:
Small world. Here's the pipe. Been hanging in my garage for about 5 years! Gonna clean it up tomorrow. [img]https://p.vitalmx.com/photos/forums/2021/11/20/519169/s1200_KRWR250pipe1.jpg[/img]
Small world. Here's the pipe. Been hanging in my garage for about 5 years! Gonna clean it up tomorrow.
Mr. Robinson wrote:
If I remember right, it will actually bolt right up to the his bike. Pretty sure all that stuff swaps over from around '99 to '12.
Should do quite a bit of stuff was interchangeble from those years
1
StormWorks 11/21/2021 10:01am
11/21/2021 10:01am
This was todays job rebuild this motor for one of our customers full recondition on the 250 motor with some mods and porting lots of new parts used she has come up real clean

12
Mr. Robinson 11/21/2021 11:53am
11/21/2021 11:53am
StormWorks wrote:
This was todays job rebuild this motor for one of our customers full recondition on the 250 motor with some mods and porting lots of new...
This was todays job rebuild this motor for one of our customers full recondition on the 250 motor with some mods and porting lots of new parts used she has come up real clean

That engine is gorgeous.
3
caviar&cigarettes338 11/21/2021 1:39pm
11/21/2021 1:39pm Edited Date/Time 11/21/2021 1:40pm
caviar&cigarettes338 wrote:
Put old tires on tell I can find some Dunlop rrs [img]https://p.vitalmx.com/photos/forums/2021/11/21/519220/s1200_D5D427CA_2ABB_4C4C_B197_3B4779AA3809.jpg[/img]
Put old tires on tell I can find some Dunlop rrs
I’m missing the rim lock in this rim and one spoke that broke on removal from the stock rim . I’m having hard time finding spokes oem husky part can’t get from excel and the rim lock from the excel stock rim doesn’t work in this rim so need find one also l. I’ll find those and do that once I get a Dunlop 2002 spec tire
Aboccarossa313 11/21/2021 1:54pm
11/21/2021 1:54pm
The Dunlop 952 has the same tread pattern as the old 756 tires they used to run. The 952 is still readily available front and rear and in an 18, and 19 as well. Hope this helps!
Mr. Robinson 11/21/2021 1:55pm
11/21/2021 1:55pm
You tried Hall's Cycles in Springfield, Illinois to find parts? They know old Husky's and they'll jump through their ass to help you. Hall's Cycles
1
caviar&cigarettes338 11/21/2021 2:20pm
11/21/2021 2:20pm Edited Date/Time 11/21/2021 2:21pm
Aboccarossa313 wrote:
The Dunlop 952 has the same tread pattern as the old 756 tires they used to run. The 952 is still readily available front and rear...
The Dunlop 952 has the same tread pattern as the old 756 tires they used to run. The 952 is still readily available front and rear and in an 18, and 19 as well. Hope this helps!
Thanks for the infor was trying look up what they ran that helps a lot !!
caviar&cigarettes338 11/21/2021 2:26pm
11/21/2021 2:26pm Edited Date/Time 11/21/2021 2:28pm
Mr. Robinson wrote:
You tried Hall's Cycles in Springfield, Illinois to find parts? They know old Husky's and they'll jump through their ass to help you. Hall's Cycles
I have not yet, I have been using just Scott at Toy Tech Cycles and GP bikes here in Canada for my oem parts and Stormworks is helping me with the not available oem parts now and a big time husky lover in Ontario Canada has been helping me also !!
1
caviar&cigarettes338 11/21/2021 4:17pm
11/21/2021 4:17pm
Aboccarossa313 wrote:
The Dunlop 952 has the same tread pattern as the old 756 tires they used to run. The 952 is still readily available front and rear...
The Dunlop 952 has the same tread pattern as the old 756 tires they used to run. The 952 is still readily available front and rear and in an 18, and 19 as well. Hope this helps!
I know I won’t prob find any but I would like to find some 756RR or I know even harder to find the MC762 Spec tire that would be the real deal . A guy could hope and dream right ? Lol
Aboccarossa313 11/21/2021 5:06pm
11/21/2021 5:06pm
Aboccarossa313 wrote:
The Dunlop 952 has the same tread pattern as the old 756 tires they used to run. The 952 is still readily available front and rear...
The Dunlop 952 has the same tread pattern as the old 756 tires they used to run. The 952 is still readily available front and rear and in an 18, and 19 as well. Hope this helps!
caviar&cigarettes338 wrote:
I know I won’t prob find any but I would like to find some 756RR or I know even harder to find the MC762 Spec tire...
I know I won’t prob find any but I would like to find some 756RR or I know even harder to find the MC762 Spec tire that would be the real deal . A guy could hope and dream right ? Lol
I hear ya! Nothing better than the real thing
1
StormWorks 11/21/2021 5:27pm
11/21/2021 5:27pm
StormWorks wrote:
This was todays job rebuild this motor for one of our customers full recondition on the 250 motor with some mods and porting lots of new...
This was todays job rebuild this motor for one of our customers full recondition on the 250 motor with some mods and porting lots of new parts used she has come up real clean

Mr. Robinson wrote:
That engine is gorgeous.
Thanks dude

Post a reply to: Fast By Ferracci Husqvarna Cr 250 help needed?/ Build